Docol® Tube 700LA
Download data sheet
Download data sheet
Docol® Tube 700LA is high-strength formable precision tube with pickled hot rolled surface condition. Available in circular shapes. Rectangular, square and customized shapes and other tailoring options are available upon request. Typical uses include automotive and engineering, where durability, formability, lightness and energy absorption are important.
Docol Tube 700LA is available in circular shapes.
| Shapes | Dimensions |
|---|---|
| Circular (mmin) | 32 - 88.91.3 - 3.50 |
| Wall thickness (mmin) | 2.0 - 3.00.079 - 0.12 |
| Mill length (mm) | 6000 |
Other shapes, sizes and lengths are available upon request.
| Outer diameter (mmin) | 2.0 mm (kg/m) | 2.5 mm (kg/m) | 3.0 mm (kg/m) |
|---|---|---|---|
| 321.3 | 1.48 | — | — |
| 351.4 | 1.63 | 2.00 | — |
| 381.5 | 1.78 | 2.19 | 2.59 |
| 411.6 | 1.92 | 2.37 | 2.81 |
| 44.51.75 | 2.10 | 2.59 | 3.07 |
| 481.9 | 2.27 | 2.81 | 3.33 |
| 502.0 | 2.37 | 2.93 | 3.48 |
| 552.2 | 2.61 | 3.24 | — |
| 572.2 | 2.71 | 3.36 | — |
| 602.4 | 2.86 | 3.55 | — |
| 76.13.00 | 3.65 | — | — |
| 88.93.50 | 4.29 | — | — |
| Yield strength Rp0.2 (min MPa) |
Tensile strength Rm (min MPa) |
Elongation A (min %) |
|
|---|---|---|---|
| HR700LA | 700 | 740 | 5 |
Mechanical properties meet the requirements of EN 10305 (+CR2).
| C (max %) |
Si (max %) |
Mn (max %) |
P (max %) |
S (max %) |
Altot 1) (min %) |
|
|---|---|---|---|---|---|---|
| HR700LA | 0.16 | 0.60 | 2.10 | 0.025 | 0.025 | 0.020 |
Chemical composition meets the requirements of EN 10305.
If other chemical elements such as Ti, Nb or V are used, the content of these elements are reported in the inspection document.
1) This requirement is not applicable provided the steel contains a sufficient amount of other nitrogen binding elements, such as Ti, Nb or V.
| Characteristic | Circular precision tubes Tolerances meet or exceed the requirements of EN 10305-3 |
|---|---|
| Outside diameter (D) (1D < 20 mm20 ≤ D < 32 mm32 ≤ D < 44 mm44 ≤ D < 55 mm55 ≤ D < 70 mm70 ≤ D < 80 mm80 ≤ D < 100 mm | ±0.12 mm±0.15 mm±0.20 mm±0.25 mm±0.30 mm±0.35 mm±0.40 mm |
| Out-of-roundness | The diameter tolerances include the out-of-roundness |
| Thickness (T) | T ≤ 1.5 mm: ±0.15 mm T>1.5 mm: ±10% of nominal thickness or ±0.35 mm whichever is the smaller |
| Straightness | Maximum 0.15% of measured length |
| Height of internal weld bead, g;Bead removedBead not removed | g ≤ 0.3 mmg < 0.8 mm, when T ≤ 1.5 mmg < 0.6 x T, when 1.5 mm < T ≤ 3.0 mm |
| Mill length | 0/+50 mm, standard length 6000 mm |
| Exact length, single cutting | Agreed at the time of enquiry and order |
| Exact length, bundle cutting | Agreed at the time of enquiry and order |
1)For a maximum distance of 100 mm, the ends may, due to the cutting method, have diameters outside the tolerances.
| Designation | Definition |
|---|---|
| UC | Uncoated (Hot rolled and pickled, HR, S2) |
Surface is slightly oiled to protect it from corrosion during transportation and short-term storage. By request, tubes can be delivered dry, however in that case SSAB will not be responsible for any possible rust.
| Designation | Ra value |
|---|---|
| UC, HR | < 2.0 µm |
The tubes are not intended to undergo any heat treatment after welding and sizing as that may alter the mechanical properties of the material.
The tubes are oiled with anti-corrosive oil.
For information concerning fabrication, see SSAB´s brochures on www.ssab.com or consult Tech Support.
Appropriate health and safety precautions must be taken when bending, welding, cutting, grinding or otherwise working on the products.