Docol® 460HE high edge ductility

More about high edge ductility steel

Download data sheet

Select Language

Get datasheet by email

Company E-mail address

Country

Please visit SSAB’s privacy statement for more information on how we process personal data

On this page

General Product Description

The Docol HR460Y520T HE steel is the next generation of hot-rolled high-strength low-alloy steels with improved local formability for higher edge ductility and cut-edge quality.

Docol HR460Y520T HE have a new and closely controlled production method resulting in a very fine microstructure in combination with a very clean steel, resulting in greatly improved local formability while still retaining a good global formability making it suitable for stamping most geometries and will excel in demanding forming where the cut edges may limit the forming operation.

The improved cut edge quality achieved with this new way of producing Docol HR460Y520T HE with a steel less sensitive to tool-settings and –wear compared to conventional HSLA grades, make it especially suitable for fine blanking.

Combining the improved local formability with the excellent cut-edge quality Docol HR460Y520T HE will have a typical hole expansion of approx. 30 percentage points above the corresponding conventional HSLA grade.

Also the bending performance is improved and a bend radius of 0xt can be guaranteed. Docol HR460Y520T HE will excel when optimizing any fine blanking, stamping or forming operation and will push the limit on how to utilize the benefits of steel.

Docol HR460Y520T HE can after agreement be adapted and delivered as dual certified with S460MC according to EN 10149-2.

Dimension Range

Docol HR460Y520T HE is available as Hot-rolled pickled and oiled coil, slit coils and cut to length sheets in thickness of 2.00^*) - 7.00 mm and widths up to 1600 mm. Length up to 16 meters.

^*)Some restrictions may occur, and will be handled on request.

Mechanical Properties

Hide/Show specific columns Edit

Select columns to display

	Coating	Yield strength R_p0.2 (min MPa)	Tensile strength R_m (MPa)	Elongation A₈₀¹⁾ (min %)	Elongation A₅²⁾ (min %)	Hole expansion ratio ³⁾ (% typical)	Min. inner bending radius for a 90° bend
Docol HR460Y520T HE	UC	460	520 - 640	16	20	80	0.0 x t

Compare parameters

Select one parameter to compare

Yield strength R_p0.2
(min MPa)

Tensile strength R_m
(MPa)

Elongation A₈₀¹⁾
(min %)

Elongation A₅²⁾
(min %)

Hole expansion ratio ³⁾
(% typical)

Min. inner bending radius for a 90° bend

Docol HR460Y520T HE

Coating

Yield strength R_p0.2
(min MPa)

460

Tensile strength R_m
(MPa)

520 - 640

Elongation A₈₀¹⁾
(min %)

Elongation A₅²⁾
(min %)

Hole expansion ratio ³⁾
(% typical)

Min. inner bending radius for a 90° bend

0.0 x t

Expand Collapse

The mechanical properties are valid in the longitudinal direction.

Bending properties for both longitudinal and transversal direction.

¹⁾ A₈₀ value applies for thicknesses < 3.00 mm.

²⁾ A₅ value applies for thicknesses ≥ 3.00 mm.

³⁾ HER –ratio is average of three test results out of five tested samples by excluding minimum and maximum results.

Chemical Composition (ladle analysis)

Hide/Show specific columns Edit

Select columns to display

	C (max %)	Si (max %)	Mn (max %)	P (max %)	S (max %)	Al_tot (min %)	Nb (max %)	V (max %)	Ti (max %)
Docol HR460Y520T HE	0.10	0.03 ¹⁾	1.50	0.025	0.010	0.015	0.09 ²⁾	0.20 ²⁾	0.15 ²⁾

Compare parameters

Select one parameter to compare

Si
(max %)

Mn
(max %)

P
(max %)

S
(max %)

Al_tot
(min %)

Nb
(max %)

V
(max %)

Ti
(max %)

Docol HR460Y520T HE

C
(max %)

0.10

Si
(max %)

0.03 ¹⁾

Mn
(max %)

1.50

P
(max %)

0.025

S
(max %)

0.010

Al_tot
(min %)

0.015

Nb
(max %)

0.09 ²⁾

V
(max %)

0.20 ²⁾

Ti
(max %)

0.15 ²⁾

Expand Collapse

The steel is grain refined.

¹⁾ Meets the requirements of category A (thin coatings) for hot-dip zinc-coating in EN 10149-2.

²⁾ The sum of Nb, V and Ti is max 0.22%.

Tolerances

Hot-rolled (UC): Tolerances in accordance to EN 10051.

Customized dimensional and shape tolerances are available on request.

Fabrication and Other Recommendations

For information concerning fabrication, see SSAB´s brochures on www.ssab.com or consult Tech Support.

Appropriate health and safety precautions must be taken when bending, welding, cutting, grinding or otherwise working on the products.

Docol® 460HE high edge ductility

General Product Description

Dimension Range

Mechanical Properties

Select one parameter to compare

Chemical Composition (ladle analysis)

Select one parameter to compare

Tolerances

Fabrication and Other Recommendations

Docol® High Edge Ductility steel product offer

Docol® 355HE high edge ductility

Docol® 420HE high edge ductility